Distortion of compact antenna test range characteristics caused by realistic design of blended rolled edge reflectors

Rostyslav Dubrovka; Clive G. Parini; Stuart F. Gregson

doi:10.3103/S0735272724080016

Authors

Rostyslav Dubrovka Queen Mary University of London, United Kingdom https://orcid.org/0000-0001-6900-1819
Clive G. Parini Queen Mary University of London, United Kingdom
Stuart F. Gregson Queen Mary University of London, UK; Next Phase Measurements Ltd., Garden Grove, United States

DOI:

https://doi.org/10.3103/S0735272724080016

Keywords:

compact antenna test range, CATR, blended rolled edge reflectors, BRE, quiet zone, QZ, spectrum distortion, anechoic chamber

Abstract

The results of investigations of quiet zone distortion caused by realistic design artefacts of blended rolled edge reflectors (BRE) used in compact antenna test ranges (CATR) are presented. Despite thorough investigations of this type of reflector in recent years, little attention has been paid to accurate scenarios, i.e., characteristics of CATRs are observed for physically fabricated reflectors. Typically, reflectors have a fixed thickness and finite-size edges. As a result, quiet-zone (QZ) performance predicted by physical optics and physical theory of diffraction (PO/PTD) will omit certain phenomena that could potentially impact the performance of the CATR. It is usually caused by in-house or commercial PO/PTD software limitations, which consider only non-shadowed surfaces and generally omit reradiation. Parameters affected by the realized mechanical implementation are side and rear illumination of anechoic chambers, amplitude and phase ripples in the quiet zone as functions of real thickness and trimmed edges of BRE reflector, which are in the deep shadow region. Therefore, this paper concentrates on carefully examining these artefacts where a proprietary, full-wave, three-dimensional, computational electromagnetic (CEM) solver was utilized using a method of moments-based finite element solver.

References

C. W. I. Pistorius, W. D. Burnside, “New main reflector, subreflector and dual chamber concepts for compact range applications,” 1987. uri: https://ntrs.nasa.gov/citations/19880003116.
I. J. Gupta, K. P. Ericksen, W. D. Burnside, “A method to design blended rolled edges for compact range reflectors,” IEEE Trans. Antennas Propag., vol. 38, no. 6, pp. 853–861, 1990, doi: https://doi.org/10.1109/8.55582.
T.-H. Lee, W. D. Burnside, “Compact range reflector edge treatment impact on antenna and scattering measurements,” IEEE Trans. Antennas Propag., vol. 45, no. 1, pp. 57–65, 1997, doi: https://doi.org/10.1109/8.554241.
C. Parini, S. Gregson, J. McCormick, D. J. van Rensburg, Theory and Practice of Modern Antenna Range Measurements. IET, 2014.
M. Dirix, S. F. Gregson, “Optimisation of the serration outline shape of a single offset-fed compact antenna test range reflector using a genetic evolution of the superformula,” in 2021 15th European Conference on Antennas and Propagation (EuCAP), 2021, pp. 1–5, doi: https://doi.org/10.23919/EuCAP51087.2021.9411036.
R. Dubrovka, C. Parini, S. Gregson, “Validation of blended rolled edge reflector characteristics for compact test ranges,” in 2023 17th European Conference on Antennas and Propagation (EuCAP), 2023, pp. 1–5, doi: https://doi.org/10.23919/EuCAP57121.2023.10133057.
M. Dirix, S. F. Gregson, R. R. Dubrovka, “Genetic evolution of the reflector edge treatment of a single offset-fed compact antenna test range for 5G new radio applications,” in 2021 Antenna Measurement Techniques Association Symposium (AMTA), 2021, pp. 1–6, doi: https://doi.org/10.23919/AMTA52830.2021.9620676.
M. Dirix, S. F. Gregson, “Broadband evolutionary optimisation of a free form contour defined serrated edge compact antenna test range,” in 2023 17th European Conference on Antennas and Propagation (EuCAP), 2023, pp. 1–5, doi: https://doi.org/10.23919/EuCAP57121.2023.10133800.
M. Dirix, S. F. Gregson, R. F. Dubrovka, “Genetic optimization of edge treatments of single offset reflector compact antenna test ranges,” in 2022 Antenna Measurement Techniques Association Symposium (AMTA), 2022, pp. 1–6, doi: https://doi.org/10.23919/AMTA55213.2022.9955023.
S. F. Gregson, M. Dirix, R. Dubrovka, “Efficient optimization of the blended rolled edge of a rectangular single offset-fed compact antenna test range reflector using genetic evolution,” in 2022 16th European Conference on Antennas and Propagation (EuCAP), 2022, pp. 1–5, doi: https://doi.org/10.23919/EuCAP53622.2022.9769585.
T.-H. Lee, W. D. Burnside, “Performance trade-off between serrated edge and blended rolled edge compact range reflectors,” IEEE Trans. Antennas Propag., vol. 44, no. 1, pp. 87–96, 1996, doi: https://doi.org/10.1109/8.477532.
C. G. Parini, R. Dubrovka, S. F. Gregson, “Compact range quiet zone modelling: Quantitative assessment using a variety of electromagnetic simulation methods,” in 2015 Loughborough Antennas & Propagation Conference (LAPC), 2015, pp. 1–5, doi: https://doi.org/10.1109/LAPC.2015.7366106.
C. G. Parini, R. Dubrovka, S. F. Gregson, “CATR quiet zone modelling and the prediction of ‘measured’ radiation pattern errors: Comparison using a variety of electromagnetic simulation methods,” 2015.
Altair, “Feko: solving connectivity, compatibility, and radar challenges,” Web-site, 2025. https://altair.com/feko (accessed Mar. 12, 2025).