Dual-band microstrip balun with different complex load impedances in frequency bands

Authors

DOI:

https://doi.org/10.3103/S0735272723030044

Keywords:

balun, complex impedance, microstrip, phase velocity, modes, reactive components, microwave device

Abstract

The paper proposes a circuit and calculation method for dual-band microstrip balun that along with equal-amplitude and counterphase distribution of signal between outputs in two bands, ensures the transformation of complex load impedances, which are different in these bands, into a real value of input impedance of the source. In this case, the matching of device input and outputs is achieved with a high decoupling level of the latter. The proposed structure consists of cascade connection of four sections of coupled lines, two reactive elements that are implemented by stubs and the decoupling links of outputs. Three variants of circuits are presented for implementing the specified structure. The presence of elements in the circuit, the parameters of which can be specified, ensures the flexibility of designing process without any restrictions on values of loading impedances. In addition, the calculation process takes into account the difference of phase velocities of modes of microstrip coupled lines. For checking the properties of the proposed circuit and its designing technique, a microstrip balun for two working bands of frequencies with average values of 1.4 GHz and 2.8 GHz at different complex load impedances was manufactured and experimentally tested. The results of measurements well agree with the results of electromagnetic simulation; they also show that in both bands, the unbalance of amplitudes and phases at the balun outputs does not exceed 1 dB and 10 degrees, respectively, confirming the expediency of using the proposed circuit and its designing method.

References

J.-H. Sung et al., “Design method of a dual band balun and divider,” in 2002 IEEE MTT-S International Microwave Symposium Digest (Cat. No.02CH37278), 2002, pp. 1177–1180, doi: https://doi.org/10.1109/MWSYM.2002.1011860.

L. K. Yeung, K.-L. Wu, “A dual-band coupled-line balun filter,” IEEE Trans. Microw. Theory Tech., vol. 55, no. 11, pp. 2406–2411, 2007, doi: https://doi.org/10.1109/TMTT.2007.907402.

X. Gao, L. K. Yeung, K.-L. Wu, “A dual-band balun using partially coupled stepped-impedance coupled-line resonators,” IEEE Trans. Microw. Theory Tech., vol. 56, no. 6, pp. 1455–1460, 2008, doi: https://doi.org/10.1109/TMTT.2008.923338.

J. Shao, H. (Bruce) Zhang, C. Chen, S. Tan, K. J. Chen, “A compact dual-band coupled-line balun with tapped open-ended stubs,” Prog. Electromagn. Res. C, vol. 22, pp. 109–122, 2011, doi: https://doi.org/10.2528/PIERC11050205.

F. Huang, J. Wang, L. Zhu, Q. Chen, W. Wu, “Dual-band microstrip balun with flexible frequency ratio and high selectivity,” IEEE Microw. Wirel. Components Lett., vol. 27, no. 11, pp. 962–964, 2017, doi: https://doi.org/10.1109/LMWC.2017.2750021.

E. S. Li, C.-T. Lin, H. Jin, K.-S. Chin, “A systematic design method for a dual-band balun with impedance transformation and high isolation,” IEEE Access, vol. 7, pp. 143805–143813, 2019, doi: https://doi.org/10.1109/ACCESS.2019.2945049.

H. Zhang, Y. Peng, H. Xin, “A tapped stepped-impedance balun with dual-band operations,” IEEE Antennas Wirel. Propag. Lett., vol. 7, pp. 119–122, 2008, doi: https://doi.org/10.1109/LAWP.2008.921315.

P. Bhowmik, T. Moyra, “Design of a dual-band microstrip balun from the concept of rat-race coupler,” Int. J. Comput. Intell. IoT, vol. 2, no. 2, 2019, uri: https://ssrn.com/abstract=3355553.

R. Gupta, M. H. Maktoomi, V. V. Singh, M. S. Hashmi, “High impedance transforming dual-band balun with isolation and output ports matching,” Prog. Electromagn. Res. Lett., vol. 81, pp. 121–126, 2019, doi: https://doi.org/10.2528/PIERL18111604.

R. Gupta, S. Kairatova, M. Hashmi, G. Nauryzbayev, “A dual-band balun architecture with unequal port-terminations,” in 2020 50th European Microwave Conference (EuMC), 2021, pp. 848–851, doi: https://doi.org/10.23919/EuMC48046.2021.9337973.

W. Zhang, Y. Wu, C. Yu, S. Li, Y. Liu, W. Chen, “Planar compact dual-band balun with flexible frequency ratios,” Electromagnetics, vol. 37, no. 1, pp. 64–72, 2017, doi: https://doi.org/10.1080/02726343.2017.1261313.

Y. Wu, L. Yao, W. Zhang, W. Wang, Y. Liu, “A planar dual-band coupled-line balun with impedance transformation and high isolation,” IEEE Access, vol. 4, pp. 9689–9701, 2016, doi: https://doi.org/10.1109/ACCESS.2016.2640187.

W. Zhang, Y. Wu, W. Wang, X. Shen, “Planar compact dual-band coupled-line balun with high isolation,” China Commun., vol. 14, no. 2, pp. 40–48, 2017, doi: https://doi.org/10.1109/CC.2017.7868173.

R. Gupta, M. S. Hashmi, M. A. Chaudhary, “Flexible design scheme for a simple dual-band ultra-high impedance transformer and its application in a balun,” IEEE Access, vol. 8, pp. 125745–125754, 2020, doi: https://doi.org/10.1109/ACCESS.2020.3008046.

W. Zhang, Y. Liu, Y. Wu, W. Wang, M. Su, J. Gao, “A complex impedance-transforming coupled-line balun,” Prog. Electromagn. Res. Lett., vol. 48, pp. 123–128, 2014, doi: https://doi.org/10.2528/PIERL14062402.

W. Zhang, Y. Wu, Y. Liu, C. Yu, W. Chen, “Compact coupled‐line balun with complex impedances transformation and high isolation,” IET Microwaves, Antennas Propag., vol. 9, no. 14, pp. 1587–1594, 2015, doi: https://doi.org/10.1049/iet-map.2014.0775.

M. H. Maktoomi, H. Ren, M. N. Marbell, V. Klein, R. Wilson, B. Arigong, “A wideband isolated real-to-complex impedance transforming uniplanar microstrip line balun for push–pull power amplifier,” IEEE Trans. Microw. Theory Tech., vol. 68, no. 11, pp. 4560–4569, 2020, doi: https://doi.org/10.1109/TMTT.2020.3019003.

Y. C. Leong, K. Sen Ang, C. H. Lee, “A derivation of a class of 3-port baluns from symmetrical 4-port networks,” in 2002 IEEE MTT-S International Microwave Symposium Digest (Cat. No.02CH37278), 2002, pp. 1165–1168, doi: https://doi.org/10.1109/MWSYM.2002.1011855.

K. Sen Ang, Y. C. Leong, C. H. Lee, “Analysis and design of miniaturized lumped-distributed impedance-transforming baluns,” IEEE Trans. Microw. Theory Tech., vol. 51, no. 3, pp. 1009–1017, 2003, doi: https://doi.org/10.1109/TMTT.2003.808677.

X. Liu, Y. Liu, S. Li, F. Wu, Y. Wu, “A three-section dual-band transformer for frequency-dependent complex load impedance,” IEEE Microw. Wirel. Components Lett., vol. 19, no. 10, pp. 611–613, 2009, doi: https://doi.org/10.1109/LMWC.2009.2029732.

I. Prudyus, V. Oborzhytskyy, “Design of dual-band two-branch-line couplers with arbitrary coupling coefficients in bands,” Radioengineering, vol. 23, no. 4, pp. 1099–1108, 2014.

Balun prototype photo

Published

2023-01-26

Issue

Section

Research Articles