Calculation of geometric dimensions of cold cathode surface in high-voltage glow discharge electron sources
DOI:
https://doi.org/10.3103/S0735272723010028Keywords:
high-voltage glow discharge, cold cathode, anode plasma, electron beam with point focus, geometric parameters of electrode system, restrictions on geometric parameters, nonlinear equation, Steffenson’s methodAbstract
The paper proposes a new iterative algorithm for finding the transverse dimension of the cold cathode of high-voltage glow discharge electron guns, based on formulation of a nonlinear equation for the functional dependence of the cathode size on the discharge current and solving this equation using the Steffenson iterative method. A distinctive feature of the proposed calculation method is taking into account the dependence of high-voltage glow discharge current on the plasma boundary position. To obtain the corresponding nonlinear equation, we use the approximate theory of one-dimensional discharge gap and well-known statement of the discharge theory that the anode plasma occupies a definite volume, which is determined by concentration of charged particles, regardless of the geometry of the electrode system. There are specified the geometric parameters of the electronic system of the high-voltage glow discharge with a spherical cathode and a hollow anode, and also well as restrictions on the system of parameters that satisfy the requirements of completeness, consistency, and closure are introduced. On a basis of the numerical analysis of the proposed iterative algorithm convergence process, we show that in case of the restrictions on the introduced parameters system are satisfied, the method convergence is usually ensured. We compare the calculations results of the transverse dimension of the cathode of high-voltage glow discharge guns with correspondent experimental data. The comparative analysis results showed that proposed iterative algorithm application results in the difference between calculations and experimental data does not exceed a few percent. The research results and proposed iterative method for calculating the transverse dimension of the cold cathode of high-voltage glow discharge guns are of great practical value and can be directly used at the initial stage of designing gas discharge guns to assess their technological possibilities.
References
I. Melnyk, S. Tyhai, A. Pochynok, “Universal complex model for estimation the beam current density of high voltage glow discharge electron guns,” in Lecture Notes in Networks and Systems, 2021, pp. 319–341.
S. Denbnovetsky et al., “Principles of operation of high voltage glow discharge electron guns and some possibilities of their technological application,” in Proceedings of SPIE, 2017, p. 104455R, doi: https://doi.org/10.1117/12.2280736.
A. A. Druzhinin, I. P. Ostrovskii, Y. N. Khoverko, N. S. Liakh-Kaguy, A. M. Vuytsyk, “Low temperature characteristics of germanium whiskers,” Funct. Mater., vol. 21, no. 2, pp. 130–136, 2014, doi: https://doi.org/10.15407/fm21.02.130.
A. Druzhinin, I. Bolshakova, I. Ostrovskii, Y. Khoverko, N. Liakh-Kaguy, “Low temperature magnetoresistance of InSb whiskers,” Mater. Sci. Semicond. Process., vol. 40, pp. 550–555, 2015, doi: https://doi.org/10.1016/j.mssp.2015.07.030.
A. Zakharov, S. Rozenko, S. Litvintsev, M. Ilchenko, “Trisection bandpass filter with mixed cross-coupling and different paths for signal propagation,” IEEE Microw. Wirel. Components Lett., vol. 30, no. 1, pp. 12–15, 2020, doi: https://doi.org/10.1109/LMWC.2019.2957207.
A. Zakharov, S. Litvintsev, M. Ilchenko, “Trisection bandpass filters with all mixed couplings,” IEEE Microw. Wirel. Components Lett., vol. 29, no. 9, pp. 592–594, 2019, doi: https://doi.org/10.1109/LMWC.2019.2929650.
A. Zakharov, S. Rozenko, M. Ilchenko, “Varactor-tuned microstrip bandpass filter with loop hairpin and combline resonators,” IEEE Trans. Circuits Syst. II Express Briefs, vol. 66, no. 6, pp. 953–957, 2019, doi: https://doi.org/10.1109/TCSII.2018.2873227.
A. Zakharov, S. Litvintsev, M. Ilchenko, “Transmission line tunable resonators with intersecting resonance regions,” IEEE Trans. Circuits Syst. II Express Briefs, vol. 67, no. 4, pp. 660–664, 2020, doi: https://doi.org/10.1109/TCSII.2019.2922429.
M. I. Grechanyuk, A. G. Melnyk, I. M. Grechanyuk, V. G. Melnyk, D. V. Kovalchuk, “Modern electron beam technologies and equipment for melting of metals and alloys, deposition of protective coatings, production of composites condensed from vapor phase and powders,” Electrotech. Electron., vol. 49, no. 5–6, pp. 115–121, 2014, uri: https://epluse.ceec.bg/modern-electron-beam-technologies-and-equipment-for-melting-of-metals-and-alloys-deposition-of-protective-coatings-production-of-composites-condensed-from-vapor-phase-and-powders/.
G. Mattausch et al., “Gas discharge electron sources – proven and novel tools for thin-film technologies,” Electrotech. Electron., vol. 49, no. 5–6, pp. 183–195, 2014.
V. Vassilieva, K. Vutova, V. Donchev, “Recycling of alloy steel by electron beam melting,” Electrotech. Electron., vol. 47, no. 5–6, pp. 142–145, 2012.
H. Sasaki, Y. Kobashi, T. Nagai, M. Maeda, “Application of electron beam melting to the removal of phosphorus from silicon: toward production of solar-grade silicon by metallurgical processes,” Adv. Mater. Sci. Eng., vol. 2013, pp. 1–8, 2013, doi: https://doi.org/10.1155/2013/857196.
M. Miyake, T. Hiramatsu, M. Maeda, “Removal of phosphorus and antimony in silicon by electron beam melting at low vacuum,” J. Japan Inst. Met., vol. 70, no. 1, pp. 43–46, 2006, doi: https://doi.org/10.2320/jinstmet.70.43.
S. V. Denbnovetsky, V. I. Melnyk, I. V. Melnyk, B. A. Tugay, “Model of control of glow discharge electron gun current for microelectronics production applications,” in Sixth International Conference on Material Science and Material Properties for Infrared Optoelectronics, 2003, p. 64, doi: https://doi.org/10.1117/12.502174.
I. V. Melnik, S. B. Tugay, “Analytical calculations of anode plasma position in high-voltage discharge range in case of auxiliary discharge firing,” Radioelectron. Commun. Syst., vol. 55, no. 11, pp. 514–521, 2012, doi: https://doi.org/10.3103/S0735272712110064.
J. I. Etcheverry, N. Mingolo, J. J. Rocca, O. E. Martinez, “A simple model of a glow discharge electron beam for materials processing,” IEEE Trans. Plasma Sci., vol. 25, no. 3, pp. 427–432, 1997, doi: https://doi.org/10.1109/27.597256.
J. F. Epperson, An Introduction to Numerical Methods and Analysis. Wiley-Interscience, 2007.
K. D. Mathews, J. H. Fink, Numerical Methods Using MATLAB. Prentice Hall, 1998, uri: https://www.amazon.com/Numerical-Methods-Using-MATLAB-3rd/dp/0132700425/.